'HPUX' 카테고리의 글 목록

HP-UX OS별 Max Swap

HPUX : 2014. 9. 2. 23:29

11.11 & 11.23 Swap Max

swchunk * 1KB * 16384 ( swchunk : 2048 ~ 65536 , maxswapchunks MAX : 16384 )

11.31 Swap Max

swchunk * 1KB * 2147483648

저작자표시 비영리 변경금지

Posted by 2540BE400

Trackback() : Comment ()

APA config lan monitor

HPUX : 2013. 8. 15. 16:39

lan0 & lan2 를 lan monitor APA 구성

# /sbin/init.d/hplm stop
# /sbin/init.d/hpapa stop

# vi /etc/rc.config.d/netconf

INTERFACE_NAME[0]="lan0"
IP_ADDRESS[0]="100.100.200.50"
SUBNET_MASK[0]="0xffffff00"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]="up"
DHCP_ENABLE[0]="0"
INTERFACE_MODULES[0]=""
INTERFACE_SKIP[0]=""

# /sbin/init.d/net start
# vi /etc/rc.config.d/hp_apaportconf

HP_APAPORT_INTERFACE_NAME[0]=lan0
HP_APAPORT_CONFIG_MODE[0]=LAN_MONITOR

HP_APAPORT_INTERFACE_NAME[1]=lan2
HP_APAPORT_CONFIG_MODE[1]=LAN_MONITOR

# vi /etc/rc.config.d/hp_apaconf

hp_apaconf 파일에 아래 내용 추가 ( syslog 에 기록 남기기 사용)

HP_APA_USE_SYSLOG=1

# /sbin/init.d/hpapa start
# cd /etc/lanmon
# lanqueryconf -s
# vi /etc/lanmon/lanmon.ascii

FAILOVER_GROUP lan900

STATIONARY_IP 100.100.200.50

PRIMARY lan0 5

STANDBY lan2 3 ( 사이트 정책에 맞게 수정 )

# /sbin/init.d/hplm start

# lanscan -q ( 확인 )

Posted by 2540BE400

Trackback() : Comment ()

HPUX Supported File and File System Sizes for HFS and JFS

HPUX : 2013. 4. 20. 03:13

Supported_File_and_File_System_Sizes_for_HFS_and_JFS.pdf

Posted by 2540BE400

Trackback() : Comment ()

LVM Limits White Paper

HPUX : 2013. 4. 20. 03:10

LVM_Limits_White_Paper_V4.pdf

11.31 에서 # lvmadm -t

LVM Limits	VG Version 1.0	VG Version 2.0	VG Version 2.1
Max VG Size (Tbytes)	510	2,048	2,048
Max LV Size (Tbytes)	16	256	256
Max PV Size (Tbytes)	2	16	16
Max VGs	256	512	2,048
Max LVs	255	511	2,047
Max PVs	255	511	2,048
Max Mirrors	2	5	5
Max Stripes	255	511	511
Max Stripe Size (Kbytes)	32,768	262,144	262,144
Max LXs per LV	65,535	33,554,432	33,554,432
Max PXs per PV	65,535	16,777,216	16,777,216
Max Extent Size (Mbytes)	256	256	256

Posted by 2540BE400

Trackback() : Comment ()

dump 영역 vg01 로 빼기 & secondary swap 설정하기

HPUX : 2013. 4. 20. 02:48

dump 영역 vg01 로 변경하기( 11.31 기준 )

test:/work ] ioscan -m dsf

Persistent DSF Legacy DSF(s)
========================================
/dev/rdisk/disk1 /dev/rdsk/c0t8d0
/dev/rdisk/disk1_p1 /dev/rdsk/c0t8d0s1
/dev/rdisk/disk1_p2 /dev/rdsk/c0t8d0s2
/dev/rdisk/disk1_p3 /dev/rdsk/c0t8d0s3
/dev/rdisk/disk2 /dev/rdsk/c0t8d1

/dev/rdisk/disk3 /dev/rdsk/c1t9d1
/dev/rdisk/disk3_p1 /dev/rdsk/c1t9d1s1
/dev/rdisk/disk3_p2 /dev/rdsk/c1t9d1s2
/dev/rdisk/disk3_p3 /dev/rdsk/c1t9d1s3
/dev/rdisk/disk4 /dev/rdsk/c1t9d2

# pvcreate -f /dev/rdisk/disk2

# vgcreate /dev/vg01 /dev/disk/disk2

# lvcreate -C y -r n -L xxxxx vg01

# lvrmboot -d dump_lv /dev/vg00

SYNOPSIS
/usr/sbin/lvrmboot [-A autobackup] [-d dump_lv] [-r] [-s] [-v] vg_name

# crashconf -d /dev/vg00/dump_lv ( ※ crashconf -v 했을때 보이지 않게 )

# vi /etc/fstab

/dev/vg01/lvol1 ... dump defaults 0 0

# crashconf -a (or crashconf /dev/vg01/lvol1 )

SYNOPSIS
/sbin/crashconf [-adlorstv] [-i | -e class ]... [-c cmode] [-p pmode]... [device ]...

# crashconf -v 로 확인

secondary swap 설정하기

# pvcreate -f /dev/rdisk/disk2

# vgcreate /dev/vg01 /dev/disk/disk2

# lvcreate -C y -r n -L xxxxx vg01

# vi /etc/fstab

/dev/vg01/lvol1 ... swap defaults 0 0

( or /dev/vg01/lvol1 ... swap pri=1 0 0 )

# swapon -a

SYNOPSIS

    Preferred Forms
      /usr/sbin/swapon -a [-u] [-t type]...
      /usr/sbin/swapon [-e |-f] [-p priority] [-u] device ...
      /usr/sbin/swapon [-m min] [-l limit] [-r reserve] [-p priority]

# swapinfo -tm ( 확인 )

SYNOPSIS
/usr/sbin/swapinfo [-mtadfnrMqw]

http://nixdoc.net/man-pages/HP-UX/ <== ( 서버에 접속할수 없을때 HP-UX man page )

Posted by 2540BE400

Trackback() : Comment ()

HP 서버 RAID 기능 풀기

HPUX : 2013. 4. 7. 01:14

HP Blade server RAID 기능 풀기

필요한 프로그램 파일 ( saupdate.efi 만 있으면 됨 )

test:/work ] ls

BL8X0CI2.HTM;1
P410I.PDF;1

SANDMAN_.BIN;1
SAUPDATE.DOC;1
UPDATE_I.NSH;1
SAUPDATE.EFI;1

HP-UX OS 에서 efi 에 필요 프로그램 복사 & 확인

efi shell 에서 RAID 기능 풀기

shell => fs0: => cd EFI/hp/tools

Posted by 2540BE400

Trackback() : Comment ()

11.31 OS Mirror

HPUX : 2013. 4. 6. 23:31

11.31 OS Mirror 방법 ( IA )

디스크 확인

test:/work ] ioscan -m dsf

Persistent DSF            Legacy DSF(s)
========================================
/dev/rdisk/disk1         /dev/rdsk/c0t8d0
/dev/rdisk/disk1_p1 /dev/rdsk/c0t8d0s1
/dev/rdisk/disk1_p2 /dev/rdsk/c0t8d0s2
/dev/rdisk/disk1_p3 /dev/rdsk/c0t8d0s3
/dev/rdisk/disk2         /dev/rdsk/c0t8d1
/dev/rdisk/disk3        /dev/rdsk/c1t9d1
/dev/rdisk/disk4        /dev/rdsk/c1t9d2

Partition 생성위해서 partition 정보 만들기

test:/work ] vi par
3
EFI 500MB
HPUX 100%
HPSP 400MB

idisk 로 Partition 나누기

test:/work ] idisk -wf ./par /dev/rdisk/disk3
idisk version: 1.44
********************** WARNING ***********************
If you continue you may destroy all data on this disk.
Do you wish to continue(yes/no)? yes

내용 생략.......

test:/work ] insf -e

Partition 후 ioscan 으로 확인

test:/work ] ioscan -m dsf

Persistent DSF             Legacy DSF(s)
========================================
/dev/rdisk/disk1           /dev/rdsk/c0t8d0
/dev/rdisk/disk1_p1      /dev/rdsk/c0t8d0s1
/dev/rdisk/disk1_p2      /dev/rdsk/c0t8d0s2
/dev/rdisk/disk1_p3      /dev/rdsk/c0t8d0s3
/dev/rdisk/disk2            /dev/rdsk/c0t8d1

/dev/rdisk/disk3           /dev/rdsk/c1t9d1
/dev/rdisk/disk3_p1      /dev/rdsk/c1t9d1s1
/dev/rdisk/disk3_p2      /dev/rdsk/c1t9d1s2
/dev/rdisk/disk3_p3      /dev/rdsk/c1t9d1s3
/dev/rdisk/disk4            /dev/rdsk/c1t9d2

test:/work ] mkboot -e -l /dev/(r)disk/disk3

test:/work ] mkboot -a "hpux -lq" /dev/(r)disk/disk1
test:/work ] mkboot -a "hpux -lq" /dev/(r)disk/disk3

11.23 에서

# mkboot -a "boot hpux -lq" /dev/(r)dsk/c0t0d0

# mkboot -a "boot hpux -lq" /dev/(r)dsk/c1t0d0

확인

test:/work ] efi_cp -d /dev/rdisk/disk1_p1 -u /EFI/HPUX/AUTO ./pri
test:/work ] cat pri
hpux -lq

test:/work ] efi_cp -d /dev/rdisk/disk3_p1 -u /EFI/HPUX/AUTO ./alt
test:/work ] cat alt
hpux -lq

test:/work ] pvcreate -f -B /dev/rdisk/disk3_p2

test:/work ] vgextend vg00 /dev/disk/disk3_p2

test:/work ] lvextend -m 1 /dev/vg00/lvol1 /dev/disk/disk3_p2

( 나머지 LV 에 대해서도 실행 )

test:/work ] setboot -a /dev/(r)disk/disk3

mirror 전

test:/work ] lvlnboot -v
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
/dev/disk/disk1_p2 -- Boot Disk
Boot: lvol1 on: /dev/disk/disk1_p2
Root: lvol4 on: /dev/disk/disk1_p2
Swap: lvol3 on: /dev/disk/disk1_p2
Dump: lvol2 on:/dev/disk/disk1_p2, 0

mirror 후

test:/work ] lvlnboot -v
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
                    /dev/disk/disk1_p2 -- Boot Disk
                    /dev/disk/disk3_p2 -- Boot Disk
Boot: lvol1 on: /dev/disk/disk1_p2
                          /dev/disk/disk3_p2
Root: lvol4 on: /dev/disk/disk1_p2
                          /dev/disk/disk3_p2
Swap: lvol3 on: /dev/disk/disk1_p2
                          /dev/disk/disk3_p2
Dump: lvol2 on: /dev/disk/disk1_p2, 0

Posted by 2540BE400

Trackback() : Comment ()

WBEMMgmtBundle C.03.01 설치후 parstatus 가 안될때

HPUX : 2012. 8. 21. 13:03

WBEMMgmtBundle C.03.01 이후 Version 설치후 아래와 같이 parstatus 가 안될때 => PHCO_42505 설치

test # > parstatus
Note: No action specified. Default behavior is display all.
CIM_ERR_FAILED: PGS04201: Provider HP_NParComplexProvider in file /opt/wbem/providers/lib/libHPNParProvider.so cannot load library. Error: Unsatisfied code symbol 'IpmiMsgLibGetBMCCapabilities' in load module '/opt/wbem/providers/lib/libHPNParProvider.so'..
Note: Unable to get any HP_NParComplex information.
Error: Cannot determine if platform is partitionable

※WBEMMgmtBundle 3.xx , 5.xx 6.01 모두 PHCO_42505 patch 해줘야 함

아래의 사이트에서 관련정보 확인 가능

WBEM Management bundle for HP-UX 11i v3 최신 version 정보 사이트 https://h20392.www2.hp.com/portal/swdepot/displayInstallInfo.do?productNumber=WBEMMgmtBundle